LED 드라이버 에이징 테스트 랙

Below is an image showing the product’s overall appearance. Note: If you have customized the size or features of the aging rack, its appearance may vary slightly.

The computer components are packaged separately. Please install the computer tower, monitor, and other accessories in their respective slots on the burn-in rack. Connect them as shown in the two figures below.

Connect the power cord for the aging rack at the top, as shown in the figure.

See the figure below. The left-hand side (A, B, C, N) provides power to the samples. Since the aging rack has a relatively high power consumption, three-phase power is used to reduce the load on the wiring. If you only have single-phase power and all samples use the same input voltage, you’ll need to use sufficiently thick wiring to short-circuit the three phases (A, B, C) together and supply power directly from a single phase. The supply voltage for the samples should match the voltage of the samples you are connecting. On the
right, L and N provide power to the equipment; the equipment requires only a single-phase 220V power supply.
GND is the ground wire; please ensure the equipment is properly grounded.
Note: When the unit is shipped from the factory, the sample power supply and the unit’s power supply may be short-circuited with a wire. If the sample and unit have the same voltage, they can share the same power cord. When using the unit, you may decide how to connect the power cords at both points based on your specific circumstances.

Note: If your aging rack is custom-built—for example, one capable of heating up to 80 degrees Celsius—the heating module requires three-phase power. See the figure below. In this case, the equipment must be connected to a three-phase power source.

For specific details, please check the power terminals on your device. If you have any questions, please feel free to contact us.

1. System Usage

Install the sample driver as shown in the diagram below. Connect the AC input of the LED driver to the terminal marked = 1 * GB3① on the aging rack. Connect the DC output of the LED driver to the terminal marked = 2 * GB3② on the aging rack.

= 1 * GB3① is the main power switch for the aging rack. Turn on the main power switch. = 2 * GB3② is the individual power switch for each level of the aging rack. Turn on the power switch for the desired level. = 3 * GB3③ is the power switch for other equipment on the aging rack, such as computers. Turn on this switch. Then turn on the computer.

Open the aging rack software. Open System Settings.
Device Port Settings:
Test Results Save Location:

Create a new test project:

There are two types of tests: output tests and switching tests. For output tests, configure the total test duration, load mode and parameters, upper and lower limit values, and so on.

For switching tests, configure the corresponding switching times.
From this screen, you can save a test project file or open a previously saved test project file.

Click the “Test” button on the right side of the software interface to begin the test. The status of each sample station on the interface is indicated by color.

패킹리스트

1	Aging Rack	1
2	Computers and Related Accessories	1
3	CD (includes a digital user manual, warranty card, certificates, etc.)	1

LED용 광도, 색도 및 안전 성능 테스트 솔루션

고니오포토미터 시스템: LSG-6000, LSG-1890B및 LSG-1800ACCD

분광복사계 및 적분구 테스트 시스템: LPCE-2 or LPCE-3

LED Life는 LM-84에 따라 테스트 시스템을 유지합니다. LEDLM-84PL

광생물학적 방사선 안전성 시험 시스템: EN 62471-C 또는 EN 62471-P

램프 시동, 예열 시간 및 깜빡임 테스트 시스템: LSRF-3 LSP-500VARC-Pst

LED 전원 드라이버 테스터: LS2090, M9822예산 및 LSP-500VARC

IK 레벨 테스터 | 스프링 해머 충격 시험기: IK07-10, IK01-06

전기역학적 진동 발생기 시스템: LVD-100KG-6D

전기 안전 검사원: LS9955, ZRS-3H, ZY-3, TTC-1

LED 등기구용 환경 챔버 테스트 솔루션

IPX5 및 IPX6 방수 테스트: JL-56

IP5X 및 IP6X 방진 테스트 장비: SC-015

High- and Low-Temperature and Humidity Chamber: GDJS-015B

염수 분무 시험기: YWX/Q-010

UV 램프 노화 시험 챔버: UV-263LS

크세논 램프 노화 테스트 챔버: XD-80LS

오존 시험 챔버: OTC-150A

이산화황 시험 챔버: SQ-010

CFL 및 LED 조명기구용 EMC 및 EMI 테스트 솔루션

EMI 테스트 시스템: EMI-9KB or EMI-9KA

정전기 방전 시뮬레이터: ESD61000-2

EFT 면역력 측정: EFT61000-4

서지 생성기: SG61000-5

전압 강하 및 정전 발생기: CSS61000-11

링 웨이브 발생기: RWG61000-12

WWW. Lisun그룹닷컴

특허 출원

모든 권리 보유 Lisun 그룹

사전 고지 없이 변경될 수 있습니다.