강철 구슬 충격 시험

1. 제품 개봉 및 기본 사용법 익히기

1.1 주요 기술 사양

파라미터	주의 사항
Steel Ball Dimensions	Φ50 mm
Steel Ball Material	GCr15 bearing steel (magnetic)
Steel Ball Quality	500±25 g or 510 g
충격 높이	Adjustable from 0 to 1.5 m

1.2 개봉 및 내용물 확인

1.2.1 포장 해제 및 육안 검사

기기를 개봉할 때는 날카로운 도구로 외부 케이스에 흠집이 생기지 않도록 조심스럽게 다루십시오. 개봉 후에는 먼저 기기 외관을 검사하여 눈에 띄는 변형이나 찌그러짐이 없는지, 버튼이 손상되었거나 헐거워지지 않았는지 확인하십시오. 기기 또는 부속품에 이상이 발견되면 전원을 켜지 마시고 즉시 저희에게 연락해 주십시오.

1.2.2 본체 및 부속품

번호	주의 사항
①	LS-B33 Steel Ball Impact Test Main Unit
②	전원 코드
③	Steel balls, 2 in total. One is a drop ball, used for vertical impact testing; the other is a pendulum ball, equipped with a suspension ring and a special steel cable, used for horizontal impact testing.

그림 1

디지털 사용자 설명서, 소프트웨어, 보증서 및 기타 자료의 다운로드 링크가 이메일로 발송되었습니다. 가능한 한 빨리 다운로드해 주시기 바랍니다. 이메일을 받지 못하신 경우, 언제든지 저희에게 연락하여 다운로드 링크를 다시 요청해 주십시오.

1.3 장비의 적용 범위

This equipment is designed in accordance with Appendix T.6 and Figure T.1 of GB/T 4943.1-2022, Clause 15.3.3 of GB 9706.1-2020, andClause 4.13.4 of GB/T 7000.1-2023. It supports two test modes—vertical drop impact and horizontal swing impact—to simulate the collision and impact scenarios that the equipment enclosure may encounter during actual use and transportation.

2. 안전상의 주의

2.1 전기 안전

2.1.1 전원 공급 장치 요구 사항

단상 AC 220V ±10%, 50/60Hz 3구 콘센트를 사용하십시오. 접지 단자는 반드시 접지에 연결해야 합니다.

2.1.2 접지 요구 사항

계측기 접지선은 보호 접지선에 확실하게 연결되어 있으며, 보호 접지 저항은 4Ω 이하입니다.

2.2 환경 안전

2.2.1 온도 및 습도 요구 사항

Avoid using this device in environments where humidity exceeds 70% (where condensation is likely to occur) or where the temperature falls outside the range of 0–35°C. The optimal operating temperature is 25±2°C.

2.2.2 환경적 금기사항

강한 자기장과 강한 전기장이 존재하는 환경;

부식성 가스 또는 액체가 포함된 환경;

인화성 및 폭발성 분진이 있는 지역, 그리고 위험 물질이 포함된 지역;

먼지가 많고, 고온다습하며, 직사광선이 비치는 환경.

2.3 작동 안전

Operators must be familiar with the instruction manual;

Wear safety goggles during testing; do not under any circumstances extend your hands or head into the area where the steel ball strikes;

The test area must be free of debris; unauthorized personnel are prohibited from approaching. Ensure there is sufficient operating space to prevent accidental injury;

Do not leave the electromagnet powered on for extended periods to prevent the coil from burning out.

3. 장비 개요 및 조립

3.1 Rear-side View

번호	주의 사항
①	Power Cord Connection
②	전원 스위치
③	Electromagnet, used to pick up steel balls that have fallen
④	Release button: Press to release the steel ball and perform the vertical impact test.
⑤	Installation of Steel Cables and Pendulum Balls
⑥	Steel Ball Mounting Bracket, Height-Adjustable

그림 2

3.2 전면 모습

A ruler, used as a reference to verify the impact height.

그림 3

4. 시험 전 준비 사항

4.1 환경 준비

Place the equipment on a level surface and level the frame; clean the test bench to ensure that the sample support surface is rigid and flat.

4.2 샘플 준비

The specimen must be securely clamped in accordance with the standard; shaking is prohibited. Determine the impact location (vulnerable surfaces or areas prone to impact). The specimen’s surface must be clean and free of damage that could affect the test.

4.3 Parameter Verification

Confirm the impact mode: drop test/swing test; confirm the impact height: 1.3 meters, for example (or refer to the applicable standard).

5. Steel Ball Impact Test

5.1 Vertical Impact Test with a Steel Ball (Equipment must be powered on)

5.1.1 샘플 배치

Place the sample on the rigid support surface directly beneath the steel ball; adjust its position so that the impact point aligns with the target test location.

5.1.2 Impact Height Adjustment

Adjust the height of the steel ball mounting bracket, use a steel ruler to verify that the free fall height is 1.3 meters, and tighten the bracket screws.

5.1.3 Placement of Steel Balls

Connect the power cord and turn on the main unit’s power switch; place the steel ball directly beneath the electromagnet and make sure it is securely attached.

5.1.4 Impact Execution

Evacuate all unauthorized personnel to a safe area; press the release button to de-energize the electromagnet and release the steel ball, thereby completing the vertical impact test. If the steel ball bounces back, catch it to prevent a secondary impact.

If no further vertical impact tests are required, turn off the power switch on the equipment.

5.1.5 Verification of Test Results

Observe the sample’s appearance, structure, protective performance, and other characteristics in accordance with the standard requirements.

5.2 Horizontal Impact Test with a Pendulum Steel Ball (No power required for the equipment)

5.2.1 샘플 배치

Place the sample within the swing path of the oscillating steel ball.

5.2.2 Steel Rope Adjustment

Adjust the length of the steel cable attached to the pendulum ball to ensure that the ball strikes the target point precisely when it falls.

5.2.3 Steel Ball Height Adjustment

Lift the pendulum so that the point where it falls is 1.3 meters vertically above the impact point; keep the steel cable taut, with no slack.

5.2.4 Impact Enforcement

Gently release the steel ball; it will strike the specimen along the swing path, completing the horizontal impact test. If the steel ball rebounds, catch it to prevent a secondary impact.

5.2.5 Verification of Test Results

Observe the sample’s appearance, structure, protective performance, and other characteristics in accordance with the standard requirements.

6. 장비의 일상 유지보수 및 관리

6.1 Routine Maintenance (After Each Test)

Store the steel ball and steel cable separately and securely; return the steel ball mounting bracket to its original height; remove the test specimen; wipe down the equipment surface, support platform, and control panel with an antistatic, dry cloth; check that the steel ball is not deformed and the steel cable shows no signs of wear; confirm that the electromagnet is not overheating and does not emit any unusual odors.

6.2 Regular Maintenance (Once a Month)

Apply grease or rust-preventative oil to the steel balls and electromagnets to prevent rust; inspect the adjustable mounting brackets and add lubricant; tighten all loose screws and joints.

6.3 Storage and Maintenance (During Extended Periods of Non-Use)

Store in a dry, well-ventilated environment with humidity ≤ 75%; remove all steel balls and store them separately to prevent rust; turn off the main power supply and cover the equipment with a dust cover; do not subject the equipment to heavy pressure or impact.

7. 문제 해결 및 일반적인 문제 해결 방법

실패 증상	가능한 원인들	순서
Severe overheating of the electromagnet	Prolonged power-on, coil aging	Turn off the power immediately and reduce the duration of each power-on cycle; contact us to replace the coil parts.

Appendix A: Comparison Table of Relevant National Standard Test Requirements

표준 번호	관련 조항	Steel Ball Specifications (Diameter + Mass + Material + Requirements)	충격 높이	시험 방법	테스트 요구 사항	결과 결정
GB / T 4943.1-2022	Appendix T.6, Figure T.1	Φ50 mm, weight 500 g ± 25 g, GCr15 bearing steel (magnetic), with the pendulum ball equipped with a suspension ring	1.3 m (vertical clearance, measured from the bottom of the steel ball to the impact surface of the specimen)	Vertical ball drop (flat impact) and swinging ball (direct impact)—choose between the two methods as needed	Samples must be rigidly secured with no looseness; the impact points are the weakest and most impact-prone areas of the product’s casing, and each impact point is struck only once.	No damage that poses an unacceptable risk; the housing has no breaks or cracks, its protective function remains intact, and it does not affect the normal operation of the equipment.
GB 9706.1-2020	15.3.3		1.3 m (vertical distance from the center of the steel ball to the impact surface of the specimen)	Vertical drop test (flat specimen), horizontal pendulum impact test (flat specimen); only one impact per relevant area	For finished products or representative components without reinforced parts, use rigid supports in their normal operating positions; this does not apply to flat-panel displays or flat glass used in ME equipment.	No ongoing damage that poses an unacceptable risk; the housing shows no permanent deformation or cracks, and the electrical safety and functionality of the equipment are not affected.
GB / T 7000.1-2023	4.13.4	Φ50 mm, weight 0.51 kg (510 g), GCr15 bearing steel (magnetic)	1.3 m (vertical free-fall height, no initial velocity, from the bottom of the steel ball to the impact surface of the specimen)	Only vertical ball impact; the direction of impact is perpendicular to the sample’s impact surface; each vulnerable area is impacted once, with no additional initial velocity.	The luminaire housing must be securely fastened so that it does not wobble; the impact areas are the vulnerable parts of the luminaire housing (such as the lampshade and the corners of the housing). Samples must be clean and undamaged, and the support surface must not provide any cushioning.	The housing shows no structural cracks and has not been opened; the internal components show no displacement or damage; the protection rating remains unchanged; the lamp functions normally and is safe to use; and there is no risk of electrical leakage.