요약 : In the quality verification of automotive components, hardware fasteners, surface coating materials and electronic components, the Composite Salt Spray Test Chamber has become critical equipment for evaluating corrosion resistance under cyclic environmental conditions. IEC 60068-2-52 is an internationally accepted standard for cyclic composite salt spray corrosion testing. Different from conventional continuous salt spray tests, this standard adopts alternating cycles of salt fog exposure, damp heat, storage and drying, which can better simulate the real corrosion and aging process of products exposed to outdoor, coastal and road de-icing environments. Taking the LISUN YWX/Q-010X Composite Salt Spray Test Chamber as the research object, this paper introduces the structural design, control logic and functional configuration of the Composite Salt Spray Test Chamber, sorts out the key implementation points of cyclic corrosion testing in accordance with IEC 60068-2-52, and compares the testing capacity between standard salt spray testers and Composite Salt Spray Test Chamber. It provides reference solutions for laboratory technicians, R&D engineers and third-party testing institutions to carry out compliance tests. As a customized type of Composite Salt Spray Test Chamber for the automotive industry, the Automotive Composite Salt Spray Test Chamber can meet stringent cyclic corrosion verification requirements for automotive chassis parts, body fasteners, electroplated decorative parts and new energy vehicle structural components, and plays an important role in the access certification of complete vehicle parts.
The chamber material of the 복합 염수 분무 시험 챔버 directly determines the long-term operational stability and leakage resistance. The LISUN YWX/Q-010X Composite Salt Spray Test Chamber is integrally formed from imported corrosion-resistant PP plates. There are no welding seams during the forming process, which fundamentally eliminates the risk of salt solution leakage and corrosive liquid overflow. Salt fog medium has strong permeability. Under long-term alternating cold and heat and salt fog immersion conditions, conventional welded chambers tend to suffer from intergranular corrosion, cracking and leakage at welding joints. This may lead to equipment damage, test interruption, sample contamination and secondary corrosion hazards in the laboratory. The seamless integrally molded PP chamber resists weak acid, weak alkali and sodium chloride solution corrosion. Meanwhile, the material provides stable thermal insulation performance, which helps maintain uniform temperature distribution inside the chamber and reduces the continuous load of the temperature control system.
The inner cavity of the Composite Salt Spray Test Chamber is equipped with independent spray pipelines, diversion structures and waste liquid collection loops. The inner corners of the chamber are designed with rounded transitions to reduce salt solution accumulation and crystallization. The matching chamber cover adopts an inclined diversion design. Condensed water can flow back to the waste tank along the inner wall to prevent condensate from dripping onto test samples. This avoids extra water droplets interfering with the corrosion process and ensures controllable test conditions. The Automotive Composite Salt Spray Test Chamber is optimized in cavity volume, sample rack load capacity and fixture layout. It can accommodate automotive metal components and coated panels of various specifications and support synchronous testing of batches of samples.
The Composite Salt Spray Test Chamber is equipped with a high-precision temperature and humidity control system and a programmable spray module. Unlike basic salt spray testers which only support fixed continuous spray modes, the programmable module allows users to freely edit multi-stage test procedures and automatically switch between spray, damp heat holding, drying and idle stages. This is the core foundation for completing cyclic tests specified by IEC 60068-2-52. The equipment supports NSS neutral salt spray, ASS acid salt spray, CASS copper accelerated acetic acid salt spray and other basic salt spray test modes. Users may select salt solution formulas and basic spray parameters according to product specifications, and combine drying and damp heat steps to build a complete cyclic scheme.
In terms of intelligent configurations, the Composite Salt Spray Test Chamber integrates an automatic defogging component. It can quickly remove fog on the inner wall during drying and damp heat phases, allowing operators to observe sample surface conditions when the program is paused. It also reduces the influence of fog adhesion on the acquisition accuracy of temperature and humidity sensors. The built-in real-time data recording system continuously collects and stores parameters including internal temperature, humidity, spray duration, sedimentation rate and running stage. After the test is completed, the complete test record can be exported for report filing and traceability. The equipment is equipped with low liquid level protection and over-temperature protection. When the liquid tank level is insufficient or the chamber temperature exceeds the set threshold, the system triggers an audible and visual alarm and can automatically stop the running program to avoid sample failure and further equipment damage.
IEC 60068-2-52 defines multiple grades of cyclic corrosion tests. Each grade consists of salt fog exposure, damp heat environment and drying environment with different durations. The full test cycle takes a long time and requires high stability of equipment during extended continuous operation. Before starting a test with the Composite Salt Spray Test Chamber, operators shall complete equipment calibration, including salt fog sedimentation calibration, temperature and humidity verification and spray uniformity confirmation. The sedimentation rate shall be controlled within the range specified by the standard, and the deviation of sedimentation at different positions inside the chamber shall be limited to guarantee consistent corrosion conditions for samples in the same batch.
Sample placement shall comply with standard requirements. Samples shall be kept at the specified inclination angle relative to the vertical direction, and sufficient gaps shall be reserved between samples to avoid shielding. The sample surface shall not be blocked by the chamber or brackets. During program setup, parameters for each stage shall be configured sequentially according to the time sequence of the selected grade. The controller of the Composite Salt Spray Test Chamber supports editing of thousands of program segments, which can fully reproduce the standard cyclic sequence and run automatically without manual switching between working conditions. During testing, the real-time recording function automatically retains full-process data. Auditors can trace environmental parameters of every stage to confirm no deviation from standard limits, ensuring valid test results and meeting the original record review requirements of certification bodies. The Automotive Composite Salt Spray Test Chamber is frequently used for high-severity cyclic tests under this standard to match the corrosion technical specifications of OEM components.

| 항목 | 사양 LISUN YWX/Q-010X 복합 염수 분무 시험 챔버 | Corresponding Requirements of IEC 60068-2-52 |
|---|---|---|
| 상공 회의소 자료 | Imported PP plate, integrally formed without welding seams | Salt fog corrosion resistance, no leakage to contaminate samples |
| 온도 제어 범위 | RT+10℃~70℃ | Multi-stage temperature control for salt spray, damp heat and drying |
| 습도 조절 범위 | 45 % RH ~ 98 % RH | Support high humidity for damp heat stage and low humidity for drying stage |
| 지원되는 테스트 모드 | NSS / ASS / CASS / Custom cyclic composite corrosion | Flexible configuration for all cyclic schemes of IEC 60068-2-52 |
| 프로그램 제어 | Programmable multi-cycle operation with automatic condition switching | Automatic long-cycle testing with minimal manual intervention |
| 추가 기능 | Automatic defogging, real-time data logging, low liquid / over-temperature alarm | Stable long-duration testing and traceable data |
With increasingly stringent anti-corrosion requirements for products, single continuous salt spray testing can no longer simulate complex natural corrosion environments. Cyclic composite corrosion testing has gradually become a regular item for product certification. Equipped with leak-proof integrated chamber, high-precision temperature and humidity control and programmable spray system, the 복합 염수 분무 시험 챔버 can stably reproduce the alternating corrosive environment specified in IEC 60068-2-52, providing reliable test conditions for product R&D validation, incoming quality control and third-party compliance certification. As a specialized variant, the Automotive Composite Salt Spray Test Chamber has been widely adopted in the automotive component industry. It helps enterprises identify corrosion weak points of coatings, plating layers and base materials in advance, optimize surface treatment processes and reduce the risk of product corrosion failure during service life. The LISUN YWX/Q-010X Composite Salt Spray Test Chamber covers both basic salt spray tests and composite cyclic corrosion tests. One single unit can satisfy multiple standard test tasks, lower laboratory equipment investment and improve the efficiency of corrosion test projects.
태그 :YWX/Q-010X귀하의 이메일 주소는 공개되지 않습니다. 필수 필드가 표시됩니다 *